Peugeot 208 Key Replacement
It is best to delegate the replacement of Peugeot keys 208 to auto locksmiths that have the equipment and expertise. They can make and program new keys much quicker than a dealership and at a lower price.
If the key fob has stopped locking or unlocking your doors, it could be due to a dead coin battery. There are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also making it impossible to start the engine. If this is the scenario, you'll need utilize the backup starting method which is explained in the owner's manual of your vehicle.
The spark plugs can also be worn out. The spark plugs are responsible for instigating the fuel which starts the engine. They are only able to last for a short time. If they are not used enough, they will eventually fail.
There is a simple solution for this problem. Check the voltage of the battery using a multimeter. If the voltage is lower than 11,5 volts then it's time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by lifting the rubber covers that cover the two terminals on the battery and using a wire brush to remove any corroded areas of the battery. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 won't start and the battery has not gone flat, you should check the spark plugs. You might find that they are simply too dirty and do not spark. peugeot key can be fixed easily by cleaning the spark plugs in the workshop.
Peugeot cars have keys that are transponder-type and works with the car's ignition system. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't transmit the correct signal to the vehicle.
This is a frequent issue that can be caused by water damage. This is a typical issue in warmer climates where the vehicle has been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who will have all the tools and equipment needed to reprogram the new key. They will also have all the latest technology and equipment needed to create a Peugeot smart key. The process shouldn't last more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot replaced the old transponder chips with a brand new model that is based on electronic components mounted on a circuit board. The new system is effective when it's brand new, however, over time, the circuit boards start to degrade and stop working properly.
This could stop the immobiliser chip from working, so your car won't start. Contact an Peugeot specialist, or a locksmith, if this is the case.
Another issue that is common is when the key fob battery is dying, this causes the key blade to stop feeding into the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a simple fix.
Faulty Receiver Module
It could be that the receiver module is malfunctioning If your Peugeot key fob doesn't work after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the onboard computer, which is responsible for controlling the centralized locking system within your Peugeot vehicle.
The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. Water can damage the chip in the event that it is exposed water for long periods of period of. The high salt content of the pool or ocean waters could cause damage to the key fob when it is submerged.
The module will have to be replaced if your Peugeot spare key no longer works. This can only be completed by an experienced auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by a unique immobilizer system that requires the right coding for the start of the engine. This is why you should only be able to trust a professional Peugeot locksmith with the task of designing and programming an appropriate replacement.
Computer on board is not working properly
The computer on board of your Peugeot is responsible for a variety of features in your car, including power windows and airbags. The on-board computer will show a code when something goes wrong. The code is stored in the system until the problem is fixed. In most cases, this will require replacing the on-board computer.
One of the most common causes of the airbag light turning on is loose or corroded connectors in the airbag sensor. This could be due to wear and tear, ageing, or exposure to salt and moisture. It is crucial to get this issue addressed as quickly as you can, as a malfunctioning airbag can be risky in the event of an accident.
If your Peugeot is showing a card that is not being detected error then the key battery in the key fob might be dead or weak. This will stop the key fob from sending a signal that will disable your vehicle's immobilizer. Try this by pressing the unlock button on the key fob and then trying to start your vehicle. If this fails then the battery in the key fob is in need of replacement.